Home / All / Limit Meter / Energy Limiter /

High efficiency Energy Limiter for Solar, Wind or Hybrid Power

High efficiency Energy Limiter for Solar, Wind or Hybrid Power

High efficiency Energy Limiter for Solar, Wind or Hybrid Power
CategoriesLimit Meter / Energy Limiter
BrandZOYEA
Update TimeDec 2,2024
Detail Information
Introduction
This is a single-phase two-wire electronic active Energy Limiting Meter, front board, wall mounting, with build-in Energy Limiter inside. It can set the daily maximum load limit.
Besides Energy Limiting function, other common functions of this Energy Limiting Meter (eg: measuring accuracy) completely accord with relevant technical requirements of class 1 single phase active energy meter, stipulated in international standard IEC 62053-21. 
There are 50Hz or 60Hz 2 type meters available which can accurately and directly measure 50Hz or 60Hz active energy consumption from single phase AC electricity net. 
It can be installed to use indoor.
Application
This Energy Limiting Meter is ideal in SOLAR, WIND or HYBRID POWER etc some new power plants.
It’s suitable for applications where the amount of energy is limited or rationed per day.
It’s useful for tenants, rugged or remote villages, isolated islands.
It also can be equipped for requiring subsidized billing.
General Function
The simplest Energy Limiting Meter is a unique new  energy meter that limits energy consumed per day to prevent energy over use. 
The built-in MCU handles all metering and control function. 
This Energy Limiting Meter is equipped with a real time clock and a load relay. 
This Energy Limiting Meter also has warning LED indicator to show the status of load relay.
And it is equipped with Overload Current Protection to make it more safer.
Operation Overview
Each Energy Limiting Meter can set the starting time (eg: 6:00pm) everyday when the new allocation will begin. As soon as the designated time (6:00pm) is reached, the new allocation will take effect.
Each Energy Limiting Meter can set daily limit of energy consumed. 
When the daily limit is reached, the meter will automatically cut off the load power, until the next day, a new kWh allocation is provided and take effect when the designated starting time (6:00pm) is reached. 
It runs in circle this way. 
Features
▲ Daily Energy Limit
▲ Overload Current Protection
▲ Load Relay Warning LED Indicator
▲ 6-digits LED display
▲ Hand Held Unit or Programm in computer setup
▲ Build-in Real Time Clock
▲ Build-in MCU, Standalone Operation
▲ Accuracy Class 1.0
▲ Front Board/Wall Mounting
▲ Wide Rage Current Measurement
▲ Easy Installation & Easy Setup
▲ Light Weight & Good Reliability
Overload Protection 
(1). Overload Protection : 
Usually the maximum current for the Energy Limiting Meter is 10A only.
When the current reach 20A, the meter will turn off in 30 seconds;
When the current reach 30A, the meter will turn off in 15 seconds;
When the current reach 40A, the meter will turn off in 5 seconds.
If the meter overload, LED is blinking "P_OV".
(2). Restore:
The Energy Limiting Meter will restore after 30 seconds for over-load off. If over-load is still there, it 
will perform the over-load protection process. 
After 10 attempts, it will stop the restore operation. 
At this time, the users have to restore it manually.
Buzzer Function
Buzzer will beep when alarm energy ( Watthour ) is reached, beep 1 second, after 4 seconds beep 1 second again, in 5 seconds cycle, till the limit is up.
Setup Options
The Pre-paid Energy Limiting Meter can be 
set/controlled by Contactless IC Card which is controlled by IC Card Reader/Writher through computer.
Contactless IC Card Function
Contactless IC Card can be read or written by IC Card Reader/Writer through computer, it’s much easier for electricity sale and user’s information management.
Once Contactless IC Card close to inducing area of the meter, IC Card will exchange data with meter bidirectionally.
User must purchase electricity first by User Card, then user close User Card to inducing area of corresponding meter, after read electricity purchased from User Card, meter switch on.
Contactless IC Card Reader-Writer
Ordering Code
Rate Voltage ( V )
Rate Current ( Ib/Imax ) A
Operating Current Range(A)
Meter
220 ~ 240
5 ( 20 ) A
0.04% Ib ~ Imax
HHU
RJ11 Power
PLC DC-Com
Data A+, B- ( 2-wire )
Technical Specification   
Connecting Mode
Direct Connections
Accuracy Class 
Class 1.0
Reference Voltage (Un)
220 ~ 240 V AC 
Network
1 phase 2 wire
Operating Voltage
187 ~ 288 VAC  
AC Voltage withstand
2 KV for 1 minute
Impulse Voltage
6kV-1.2/50μS waveform
Rate Current (Ib)
5 A direct connection
Maximum Rates Current (Imax)
20A & 40A direct connection
Operating Current Range
0.4%Ib ~ Imax
Operating Frequency Range
50 Hz ± 10%
Internal Power Consumption
<3W/5VA
Operating Humidity Range
<95%
Storage Humidity Range
<75%
Operating Temperature Range
-20℃ ~ + 55℃
Storage Temperature Range
-30℃ ~ + 65℃
Pulse Output rate (meter constant)
4000 imp/kWh
Display
6-Digits Register, LED Display (L)
Reference Standard
IEC62053-21
Overall Dimensions (W x H x D)
W: 177 mm x H: 116 mm x D: 66 mm
Overall Dimension                                                                     Installation
Application
Please send your message to us
*Email
Tel
*Title
*Content
Upload
  • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.
newsletter

Subscribe to the Molotok mailing list to receive updates on new arrivals, special offers and other discount information.

subscription
our locations
Tel:

86-571-86455045

Email:
Address:
2-1218, Zhongtian MCC, Tongpu Road, Hangzhou, China